lp:debian/libpam-afs-session

Related source package recipes

No recipes using this branch. (?)

Create packaging recipe

Related snap packages

Related bugs

Related blueprints

17. By Russ Allbery on 2015-09-19

* New upstream release.
  - Fix PAM_REINITIALIZE_CRED and PAM_REFRESH_CRED handling in
    combination with opening a new session. Fixes failure to isolate
    tokens when used with sudo. (Closes: #782589)
* Remove erroneous branch information from Vcs-Git.
* Prefer *.tar.xz in debian/watch to match packaging.
* Add debian/gbp.conf reflecting the branch layout of the default
  packaging repository.
* Refresh upstream signing key.
* Update standards version to 3.6.6 (no changes required).

16. By Russ Allbery on 2014-04-13

* Remove now-unnecessary dh_builddeb override to force xz compression.
* Convert debian/copyright to copyright-format 1.0.
* Specify the Debian packaging branch in the Vcs-Git control field.
* Add the upstream release signing key and verify it in debian/watch.
* Update standards version to 3.9.5 (no changes required).

15. By Russ Allbery on 2013-06-23

* Apply upstream patch to add AM_PROG_AR to configure.ac, now apparently
  required by Automake for the binutils in unstable. (Closes: #713292)
* Apply upstream patch to build with largefile support. This is
  probably pointless for this module, but consistency is good.
* Switch to xz compression for the binary package and *.debian.tar file.
* Enable parallel builds.
* Canonicalize the Vcs-Git and Vcs-Browser URLs.
* Update standards version to 3.9.4 (no changes required).

14. By Russ Allbery on 2012-02-06

* Enable bindnow hardening flags.
* Change the architecture of the package to linux-any, since there is no
  OpenAFS support for the FreeBSD kernel yet.
* Bump debhelper dependency to 9 now that compatibility mode V9 is no
  longer experimental.
* Regenerate the Autotools build system with dh-autoreconf.
* Move single-debian-patch to local-options and patch-header to
  local-patch-header so that they only apply to the packages I build and
  NMUs get regular version-numbered patches.

13. By Russ Allbery on 2011-07-25

* New upstream release.
  - Reset the SIGCHLD handler while spawning an external aklog program
    so that the application SIGCHLD handler isn't invoked when aklog
    exits. (Closes: #630609)
* Convert to multiarch. Depend on the multiarch version of
  libpam0g, install the module into the multiarch version of
  /lib/security, and declare the package Multi-Arch: same.
* Update to debhelper compatibility level V9 (experimental).
  - Build-Depend on debhelper 8.1.3 or later.
  - Add Pre-Depends: ${misc:Pre-Depends}.
  - Add Lintian override for using an experimental debhelper level.
* Remove unnecessary debian/dirs file.

12. By Russ Allbery on 2011-06-08

* New upstream release.
  - Fix memory allocation bug in the previous release.

11. By Russ Allbery on 2011-06-07

* New upstream release.
  - Honor KRB5CCNAME from the general environment if it is set and that
    variable is not set in the PAM environment, rather than declining to
    run aklog. (Closes: #621496)
* Update standards version to 3.9.2 (no changes required).

10. By Russ Allbery on 2011-03-03

* New upstream release.
  - Return PAM_SUCCESS instead of PAM_IGNORE from pam_setcred if AFS is
    not available or if we're deleting credentials but the PAM module is
    configured not to delete tokens. Returning PAM_IGNORE from
    pam_setcred confuses the Linux PAM library.
  - Fix error return statuses for pam_setcred.

9. By Russ Allbery on 2010-08-11

* Apply upstream deltas:
  - [3e57d766] Don't return an initialized value when notokens is set
* Install a pam-auth-update profile for pam_afs_session that runs it
  from the additional section during both auth and session. Thanks,
  Nate Coraor. (Closes: #523796)
* Remove libpam-openafs-session transitional package. This package was
  needed for upgrades from etch to lenny.
* Add ${misc:Depends} to dependencies.
* Change section to admin to match override.
* Update standards version to 3.9.1 (no changes required).
* Explicitly declare source format 1.0 for right now.

8. By Steve Langasek on 2009-09-10

No-change rebuild against libkrb5-3