lp:~digitalcircuit/flashlight-firmware/anduril2_opt_ramp_low_slower

Branch merges

Propose for merging

No branches dependent on this one.

Rejected for merging into lp:~toykeeper/flashlight-firmware/anduril2

Selene ToyKeeper: Pending requested 2021-07-13

Diff: 46 lines (+24/-1)

2 files modified

ToyKeeper/spaghetti-monster/anduril/ramp-mode.c (+10/-1)
ToyKeeper/spaghetti-monster/anduril/ramp-mode.h (+14/-0)

api

Related source package recipes

No recipes using this branch. (?)

Create packaging recipe

Related snap packages

Related bugs

Related blueprints

595. By Shane Synan on 2021-07-13

slower ramp with RAMP_SMOOTH_HALF/QUARTERSPEED_LEVEL

Added two new #define options to further slow down ramping speed near
floor, RAMP_SMOOTH_HALFSPEED_LEVEL and RAMP_SMOOTH_QUARTERSPEED_LEVEL.

If neither are set, no change to ramping.

If either are set, when ramp is at/below HALF or QUARTER level, smooth
ramping speed is slowed down by a half or fourth, respectively. This
may make it easier to manage low moonlight levels on drivers with
limited precision near moonlight.

NOTE: PWM#_LEVELS should still be non-linear and determined via
level_calc.py! This should only be used when there's no possible
additional precision to have in near-moonlight levels.

594. By Selene Scriven <email address hidden> on 2021-07-11

rewrote hybrid memory (manual memory timer) to eliminate corner cases

Old method:
  - at 1-click power-on, choose a brightness based on off-time
    (manual level or last-ramped level)

New method:
  - when off longer than the timer, set last-ramped level to manual level

This fixes a bug:
  - turn light off
  - wait for timer
  - turn light on with a shortcut to moon
  - turn light off
  - turn light on
  - pre-patch, light went to last-ramped level instead of manual level

This change also reduces the ROM size slightly.

593. By Selene Scriven <email address hidden> on 2021-07-11

added Emisar D18 Nichia 219 build target (same as normal but reduced FET power)

592. By Selene Scriven <email address hidden> on 2021-07-09

set Emisar/Noctigon "219" builds to 65% FET power
(was 75% or 80% before)
(change requested by Emisar)

591. By Selene Scriven <email address hidden> on 2021-05-23

added missing ifdefs for compiling without USE_SIMPLE_UI
(compiles now, but isn't tested on hardware)

590. By Selene Scriven <email address hidden> on 2021-05-14

oops, somehow I forgot to add this earlier... Hank's UI preferences (applies to all Emisar / Noctigon lights)

589. By Selene Scriven <email address hidden> on 2021-05-07

made manual memory remember tint too, not just brightness

588. By Selene Scriven <email address hidden> on 2021-04-14

aux LED config cleaning...

- use fancy blinking mode by default
  (define USE_OLD_BLINKING_INDICATOR if old slow mode is wanted)

- remove TICK_DURING_STANDBY from all cfg-*.h files because it's
  enabled automatically by other features anyway (autolock, memory timer)

- remove STANDBY_TICK_SPEED from cfg-*.h because all the values
  matched the default anyway so it was redundant

- set rot66 button LED to high+blinking instead of high+off
  (it was only "off" because it ran out of space, and that was resolved)

- enabled fancier indicator by default on fireflies-ui and rampingiosv3,
  since its other #define clauses were removed
  (not sure if those older UIs still compile, but if so, it's worth
  at least trying not to break it)

587. By Selene Scriven <email address hidden> on 2021-04-14

config updates for Hank (Emisar / Noctigon):
- use cycling rainbow mode by default on lights with RGB LEDs
  (instead of voltage, because it's better for impressing new users)
- use 2C turbo instead of 2C ceiling (Anduril 1 style instead of Anduril 2 style)

also some other minor housekeeping...
- make all K1 models use consistent rainbow cycling speed
- enable auto-lock and manual memory timer on Emisar D1v2
- remove redundant RGB config on Lume1 (it had incorrect comments anyway)

586. By Selene Scriven <email address hidden> on 2021-04-13

fixed missing ifdef for simple UI